So you have decided to tackle a large project, or
maybe your eyesight is diminishing, or you just need a little more help keeping
track of where you are in your stitching project so that you don’t have to
“frog” as many times as you used to. Gridding is for you.
Gridding is a way to “mark” your fabric
without actually leaving any permanent writing or prints on it. This is a truly
effective way to know that the stitch you are placing is in the correct area of
the fabric.
First, grab a chart and take a look at the
“grid” that has already been placed on there for you. The first step has already
been done! Now we only have to transfer this over to the fabric.
Supplies you need:
Sulky metallic thread in Rose or Hot pink or other bright color that does
not match your fabric or design.
After you have all your supplies together, pull
out the paper, pencil, and the leaflet once again. Look closely at the leaflet
and find the measurements of the actual design by Width x Height. Write this on
the paper. Now, look at the chart. Notice that every 10 squares, you find a
heavier line marking this chart off in 10x10 squares completely. This is the
line that we’ll place onto our fabric. If you locate the arrows on the top and
bottom of your chart, and follow them into the center of the design, this marks
the center. Use your pencil to make a light mark where the placement of the
center is. This spot should fall somewhere in the middle of one of those 10x10
squares.
At the moment, we will focus only on that 10X10
square. From the right side line of that square, count how many squares OVER
until the center spot. Do the same from the top line down to the center spot.
Write this onto the sheet of paper for future reference. It will look something
like this:
Example 1:
“Center spot: two squares over, and three
squares down”
If you find that the center point falls on the
intersecting lines, just write “at center”
We are now done with the leaflet and the pencil
at this point.
Using the metallic thread, Make a small loop
start, half stitch at the center point of your fabric. You can find the center
by folding the fabric evenly in half and then in half a second time.
Now, using a long piece of thread that will go
the width of the fabric, thread the needle. Refer to the piece of paper and
notations that you made. (following example 1)
You know
that the center is 2 squares over and 3 squares down from the top left corner of
the center 10x10 square. Starting from this point, you will make a basting
stitch going out to the left side of the fabric. Only baste half of the width of
the chart. If the width of the chart is 100W, then only stitch 50 squares
counting by 2’s. (you are only going over or under two squares
for each basting stitch)
Remember, we mentioned that the gridding is the
marking of the 10X10 squares. If you are working on aida, then you will be going
over and under on the fabric every 2 squares/threads. BUT if you are working on even weave other than aida that would be stitching 2 over 2, you will be going
over and under on the fabric every 4 squares (threads).
Once that side is done, you will rethread your
needle and baste the line that begins at the same starting point, going up.
Again, you only need to baste half of the height up.
When this is accomplished, you will complete
each line by stitching the width out to the right and the height out to the
bottom by completing the second half of the stitch width and height.
Now, you should have a stitch where the center
point on your fabric falls, and a line going top to bottom and side to side on
the fabric. This does not intersect at the center point for our example.
Remember, the center point is 2 over and 3 down from the intersection of the two
lines.
From here, you will complete each line going
across the fabric and top to bottom until you have created your grid. Remember,
each line is 10 squares from the one below, above, and to the sides.
I prefer to work the rows by beginning at the
perpendicular line (the one going up and down the fabric)
and basting all the lines that will go across the fabric to the left. Following
this center line gives me a place to easily count up by 10 squares for placement
of the next row. Once I have the left hand side complete, then I finish the
right hand side. Next I baste the top half and then finally the bottom half.
Now, the fun part begins. Pull out your leaflet
and all your thread and enjoy the stitching of the actual project!
